Home >  Carbon and Low-alloy High-strength Steel

S355ML Steel

2019-01-25 51 30 Comment

ol Process (TMCP)__ ___ TMCP steel plate S355ML under steel standard EN 10025-4.Structural Steel plate S355ML shall be done low temperature impacting test under minus 50 centi degree,and the minimum v

EN10025-2 S235JR steel grade

2019-01-25 51 30 Comment

asted and Spray Paint or as required._Standard:ASTM,EN,GB,JIS,DIN_Material:Q215A/B, Q235A/B/C/D, Q275A/B/C/D, SS330,SS400,SM400A, Cr. C, Cr.D, S235JR, ASTM A36_S235JR carbon steel plate is the Europea

S235J2 carbon steel

2019-01-25 51 30 Comment

oth ok.As rolled delivery condition without any special rolling and heat treatment condition.Normalizing rolling process in which the final deformation is carried out in a certain temperature range le

S235J0 carbon steel

2019-01-25 51 30 Comment

st shall be done under zero centigrade for structural steel plate S235J0.Normally Controlled rolled or Air rolled for steel plate S235J0 is ok,if customer demand,normalized is better for delivery of S

Q690C steel plate

2019-01-25 51 30 Comment

ndard Specification is for Rolled Steels for Welded Structure___ Q690C Specification:  Thickness: 1mm to 500mm; Width: 1500mm to 4500mm: Length: 3000mm to 27000mm___ Third Party Inspection for Q6

Q390D steel plate

2019-01-25 51 30 Comment

igrade.Normalised heat treatment suggested to be done for low alloy steel plate Q390D in heavy thickness._ Full Data Technical Requirements & Additional Services:_鈾 Low temperature impacting te

Q390C steel plate

2019-01-25 51 30 Comment

Mpa.Normlised Q390C is mainly for heavy steel plate for improve the steel property when rolling. Technical Requirements & Additional Services:_鈾 Low temperature impacting test_鈾 Cutting and

GB/T1591 Q345D structural steels

2019-01-25 51 30 Comment

malised_GB/T1591 Q345D steel shall be done charpy V-notch impacting test under minus 20 centigrade.Many container manufacturers adpots these high tension strength to make offshore containers which can

Q345C Steel Properties and Introduction

2019-01-25 51 30 Comment

trength is 345 MPa (datasheet tested with 16mm diameter steel bars or steel plates). According to GB/T 1591 鈥 2008, Q345 material has 5 quality grades: Q345A, Q345B, Q345C, Q345D and Q345E. 鈥淨鈥

GB/T1591 Q345B low alloy structural steel

2019-01-25 51 30 Comment

nt:As rolled/Control-rolled/Normalised_Steel grade Q345B is the most common used as high strength low alloy structural steel in industry area.BBN steel can offer steel coils,steel plates,angles,channe

A709 Grade 50 Steel Plate

2019-01-25 51 30 Comment

These grades are often specified with Charpy tests referencing the specific zone or lowest anticipated service temperature. The Charpy tests are specified as non-fracture critical, which is a per-heat

ASTM A633 Grade E Steel Plate

2019-01-25 51 30 Comment

ow temperatures. Grades C is available up to 4" in thickness and Grade E is available up to 6" in thickness. Typical applications are utility poles as plates, offshore platforms, construction equipmen

ASTM A633 Steel

2019-01-25 51 30 Comment

s. Grades C is available up to 4" in thickness and Grade E is available up to 6" in thickness. Typical applications are utility poles as plates, offshore platforms, construction equipment frames, elec

ASTM A572 Grade 55 HSLA Steel

2019-01-25 51 30 Comment

erial properties cards below compare ASTM A572 grade 55 to: wrought alloy steels in the same category (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the hi

A572 Grade 42 steel plate

2019-01-25 51 30 Comment

smission towers.___ _ _ _ _ Gangsteel Grade :_ _ _ _ _ A572 Grade 42_ _ _ _ _ _ _ Specification:_ _ _ _ _ Thickness 8mm-200mm, Width: 1500-4020mm,

ASTM A572/A572M A572 Grade 50 steel

2019-01-25 51 30 Comment

uccessfully machined with the appropriate techniques and is easy to weld. It is a high strength low alloy (HSLA) columbium-vanadium steel and is available in grades 42, 55, 60 and 65._ASTM A572/A572M

ASTM A285 Grade C steel plate

2019-01-25 51 30 Comment

applications including structural,mechanical and general engineering purposes___ ASTM A285 Grade C Steel Plate Specification:___ Thickness: 1-200mm,Width: 1000-4000mm,Length: 2000-12000mm___ A285 Grad

STM A283 Grade D Carbon Steel

2019-01-25 51 30 Comment

strength and lowest ductility compared to the other variants of ASTM A283 carbon steel._The graph bars on the material properties cards below compare ASTM A283 grade D to: wrought carbon or non-alloy